In England, you don’t need planning permission for a resin driveway in a front garden if the surface is permeable or drains onto a lawn or border on your property. You do need permission if you lay more than 5 m² of a front garden with an impermeable surface that drains towards the road. A resin bound drive on a porous base usually counts as permeable. Wales, Scotland and Northern Ireland have their own rules. Listed buildings, conservation areas and dropped kerbs can also change things.
Quick facts
| Situation (England) | Planning permission needed? |
|---|---|
| Front garden, permeable surface, any size | Usually no |
| Front garden, impermeable, drains to lawn or border | Usually no |
| Front garden, impermeable, over 5 m², drains to road | Yes |
| Front garden, under 5 m² | Usually no |
| Back garden | Usually no, under householder rights |
| New dropped kerb | Highways consent needed from council |
| Listed building or flat | Check with council |
This is a general guide, not legal advice. Your local planning authority has the final say.
The 5 m² rule explained
Since October 2008, the rules for householders in England changed to cut the amount of rainwater running off front gardens into drains and roads. The idea is to reduce surface water flooding.
Under these rules, you can lay a new or replacement hard surface in a front garden without planning permission if:
- the surface is permeable (water soaks through it), or
- rainwater is directed to a permeable area within your property, such as a lawn, border or soakaway
If neither applies and the area is over 5 m², you need planning permission. The rule covers the area between the front of the house and the road.
Is resin permeable?
It depends on the system and what it’s laid on.
Resin bound
Resin bound is a mix of stone and resin trowelled into a porous layer. Water drains through the resin itself. If it’s laid on a porous base, such as porous tarmac or a permeable sub-base, the whole drive is permeable. This is usually the simplest route to a planning-friendly resin drive.
Resin bound on an old solid base
Here’s the catch. If resin bound goes straight over old, solid tarmac or concrete, water passes through the resin but stops at the base. It then runs off the surface. Depending on the falls, that may need drainage to a border, a soakaway or a channel drain to stay within the rules.
Resin bonded
Resin bonded has stone scattered over a solid resin layer, so it isn’t permeable. It needs separate drainage to avoid planning permission on front gardens over 5 m². See resin bound vs resin bonded for the full difference.
Other things that can need permission
Dropped kerbs
If you’ll drive across a pavement or verge, you’ll usually need a dropped kerb (also called a vehicle crossover). This needs approval from your council’s highways team, whatever the driveway is made from. Some roads, such as classified roads, may also need planning permission for a new access.
Listed buildings and conservation areas
Extra controls may apply. In a conservation area, the council may have removed some permitted development rights. For listed buildings, changes to the setting can need consent.
Flats and maisonettes
Householder permitted development rights don’t apply to flats and maisonettes, so you may need permission.
Raising ground levels
Big changes in ground level or retaining walls can bring in other rules.
Wales, Scotland and Northern Ireland
The rules above are for England. The other UK nations have their own planning law:
- Wales has similar rules for permeable surfacing in front gardens, but check the Welsh Government guidance and your council.
- Scotland has its own permitted development rules for hard surfaces, which can apply more widely than front gardens. Check with your council.
- Northern Ireland has separate rules again.
Wherever you are, a permeable resin bound drive with good drainage is usually the safest choice. If in doubt, ask your council before work starts. Some councils offer a lawful development certificate for peace of mind.
What to ask your installer
A good installer deals with drainage and planning questions every week. Ask:
- Will the finished drive be permeable, including the base?
- Where will surface water go?
- Is a dropped kerb needed? Will you apply or should I?
- Have you laid drives in conservation areas near here?
Vague answers are a warning sign. Our questions to ask a resin flooring installer has more ideas.
A quick checklist before you book
- Measure the area of front garden you plan to surface.
- Decide whether you’ll use resin bound on a porous base or need separate drainage.
- Check whether your home is a listed building, a flat or in a conservation area.
- Check whether you need a new or wider dropped kerb.
- Ask your installer to explain the drainage in writing.
- If anything is unclear, contact your council’s planning team before work starts.
FAQs
Do I need planning permission for a resin driveway in England?
Usually not, as long as it’s permeable or drains to a lawn or border on your property. You need permission for over 5 m² of impermeable surface in a front garden that drains to the road.
Is resin bound SuDS compliant?
Resin bound on a porous base is a permeable surface, which is what sustainable drainage (SuDS) aims for. Check the base and drainage design with your installer.
Can the council make me remove a driveway?
If a drive needed planning permission and didn’t have it, the council can take enforcement action. It’s far cheaper to check first.
Do I need permission for a resin driveway in my back garden?
Usually not for a house in England, under householder permitted development, but check if you’re in a flat, a listed building or a conservation area.
Find a checked installer near you
A local installer who knows your council’s approach is worth a lot. See our resin driveway installers, search installers near you and check each firm’s Legit Score.


